Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Mon Dec 31 19:08:24 CST 2001
    grog@monorchid.lemis.com:/src/FreeBSD/5-CURRENT-MONORCHID/src/sys/i386/compile/MONORCHID
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04d4000.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1462507976 Hz
CPU: AMD Athlon(tm) XP processor 1700+ (1462.51-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x662  Stepping = 2
  Features=0x383f9ff
  AMD Features=0xc0480000<,AMIE,DSP,3DNow!>
real memory  = 536870912 (524288K bytes)
avail memory = 516669440 (504560K bytes)
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00fde60
npx0:  $on motherboard
npx0: INT 16 interface
pcib0: at pcibus 0 on motherboard
pci0: on pcib0
pcib1: at device 1.0 on pci0
pci1: on pcib1
pci1: at device 0.0 (no driver attached)
ahc0: port 0xd000-0xd0ff mem 0xea001000-0xea001fff irq 11 at device 8.0 on pci0
aic7870: Single Channel A, SCSI Id=7, 16/255 SCBs
rl0: port 0xd400-0xd4ff mem 0xea000000-0xea0000ff irq 12 at device 9.0 on pci0
rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode
rl0: Ethernet address: 00:02:44:17:f8:da
miibus0: on rl0
rlphy0: on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: at device 10.0 (no driver attached)
isab0: at device 17.0 on pci0
isa0: on isab0
atapci0: port 0xd800-0xd80f at device 17.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: port 0xdc00-0xdc1f irq 9 at device 17.2 on pci0
usb0: on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: port 0xe000-0xe01f irq 9 at device 17.3 on pci0
usb1: on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: port 0xe400-0xe41f irq 9 at device 17.4 on pci0
usb2: on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: at device 17.5 (no driver attached)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
orm0: at iomem 0xc8000-0xc87ff,0xc0000-0xc7fff on isa0
atkbdc0: at port 0x64,0x60 on isa0
atkbd0: flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
pmtimer0 on isa0
ppc0: at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE
Probing for PnP devices on ppbus0:
ppbus0: PRINTER ESCPL2,BDC,D4
plip0: on ppbus0
lpt0: on ppbus0
lpt0: Interrupt-driven port
ppi0: on ppbus0
sc0: at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: can't assign resources
unknown: can't assign resources
unknown: can't assign resources
unknown: can't assign resources
unknown: can't assign resources
unknown: can't assign resources
ad0: 13042MB [26500/16/63] at ata0-master UDMA66
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 0 lun 0
sa0: Removable Sequential Access SCSI-2 device 
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
sa1 at ahc0 bus 0 target 4 lun 0
sa1: Removable Sequential Access SCSI-2 device 
sa1: 10.000MB/s transfers (10.000MHz, offset 7)
Mounting root from ufs:/dev/ad0s1a$